Invacare Mobility Aid Fixed Released Rail Cane Clamps User Manual

Twist Release Cane Clamps  
Quick Release Rail Clamps  
Fixed Released Rail/Cane Clamps  
Assembly,Installation and Operating Instructions  
NOTE:CheckALLpartsforshippingdamagebeforeuse.  
In case of damage, DO NOT use. Contact Carrier/Dealer  
for further instruction.  
PROCEDURE 1 - INSTALLING  
CLAMPS ON SEATING SYSTEMS  
WITH A GROWTH BRACKET  
SAFETY SUMMARY  
Twist Release Clam ps For Back (FIGURE 1)  
The following recommendations are made for the safe  
installationanduseofmountinghardwareonseatingsys-  
tems:  
NOTE: Refer to INSTALLATION WARNING in the  
SAFETY SUMMARY before proceeding.  
1. Make sure that the back mounting hooks are flush  
against the back canes.  
G ENERAL WARNINGS  
DO NOT insta ll this e quipme nt without first re a d-  
ing a nd understa nding this instruction sheet. If you  
a re una ble to unde rsta nd the se instruc tions, c on-  
ta c t a he a lthc a re profe ssiona l, de a le r or te c hni-  
c a l pe rsonne l if a pplic a ble be fore a tte mpting to  
insta ll this equipment - otherwise, injury or da m-  
a ge ma y oc c ur.  
2. Loosen socket screw that opens twist release clamp.  
NOTE: There is a right and left twist release clamp. Make  
sure when installing that the socket screw adjustment is  
on the outside of the wheelchair frame.  
3. Install the open end of the twist release clamp below  
the back mounting hook so that the locking mecha-  
nism rests on top of the back mounting hook.  
Ensure tha t the se a t a nd ba c k of the se a ting sys-  
te m a re fixe d to the whe e lc ha ir. A loose sea t or  
ba c k ma y le a d to pote ntia lly da nge rous situa -  
tions with positioning de vic e s.  
4. Loosely tighten the socket screw.  
5. Repeat STEPS 1- 4 for the other side.  
6. Makesurebothtwistreleaseclampsareflushagainst  
thebackmountinghooksandthatthelockingmecha-  
nism rests on top of the back mounting hooks.  
INSTALLATION WARNINGS  
DO NOT insta ll twist, quic k, a nd fixe d re le a se  
c la mps in a ny othe r loc a tions tha n spe c ifie d in  
this instruction sheet - otherwise, the sea ting sys-  
te m will not be se c ure d prope rly to the whe e l-  
cha ir a nd bodily injury ma y occur.  
7. Torque socket screw to 75 - inch pounds.  
8. Once twist release mounting clamps are secured, do  
one (1) of following:  
A. Refer to QUICK RELEASE CLAMPS FOR  
SEATinPROCEDURE1ofthisinstructionsheet.  
Ensure tha t ALL ha rdwa re is tight a t ALL time s.  
B. RefertoUSINGCLAMPSinthisinstructionsheet.  
Locking Mechanism  
HARDWARE REFERENCE CHART  
NOTE:Thischartisageneralguidelineforrecommended  
mountinghardware.  
Twist Release  
Cane Clamp  
HARDWARE C LAMPS  
With  
Without  
Growth Bracket Growth Bracket  
Socket Screw  
Inside  
BACK  
SEAT  
Twist Release  
Twist Release  
FixedRelease  
(SEE FIGURE 1)  
Back  
Mounting  
Hook  
Back Cane  
(SEE FIGURE 3)  
Quick Release  
(SEE FIGURE 2)  
Quick Release  
FixedRelease  
(SEE FIGURE 4)  
Seat Rail  
FIGURE 1- TWIST RELEASE CLAMPS FOR BACK  
1
 
5. Reinstall the mounting screw, lock washer, and inter- 4. Install the quick release clamp onto the seat rail so  
nal mounting screw into the fixed release rail/cane  
clamp and torque to 75 - inch pounds.  
thatthefixedportionisflushagainstandrestsontopof  
the mounting hook and the release portion is between  
the front riggings and the mounting hook.  
6. Repeat STEPS 1 - 5 for other side.  
5. Reinstall the sleeve, lock washer, and internal mount-  
ing screw into the quick release clamp and torque to  
75 - inch pounds.  
7. Once fixed release mounting clamps are secured,  
do one (1) of following:  
A. Refer to QUICK RELEASE CLAMPS FOR  
SEATinPROCEDURE2ofthisinstructionsheet.  
6. Repeat STEPS 1- 5 for other side.  
7. Once quick release mounting clamps are secured, do  
one (1) of following:  
B. Refer to USING CLAMPS in this instruction  
sheet.  
A. RefertoFIXEDRELEASECLAMPSFORSEATin  
PROCEDURE 2 of this instruction sheet.  
B. RefertoUSINGCLAMPSinthisinstruction sheet.  
Twist Release  
Clamp  
Mounting  
Hooks  
Fixed Release Clam ps For Seat (FIGURE 4)  
Inside of Back Cane  
NOTE: Refer to INSTALLATION WARNING in the  
SAFETY SUMMARY before proceeding.  
Fixed Release  
Clamp  
NOTE: The quick release and fixed release clamps are  
designed to fit either 1-inch rail tubing or, with insert pro-  
vided, 7/8-inch rail tubing.  
Seat Rail  
1. Removethesleeve,lockwasher,and internalthreaded  
mounting screw from the fixed release clamp (DE-  
TAIL “C”).  
DETAIL “B”  
Sleeve  
2. Place the fixed release clamp on the seat rail.  
Lock Washer  
3. Iffixedreleaseclampisnottightlyfittedaroundseatrail  
Mounting  
Hook  
tubing, installinsertprovidedasshowninDETAILC”.  
4. Install the fixed release clamp onto the back rail so  
thatthefixedportionisflushagainstandrestsontopof  
themountinghookandislocatedbetweentheseatrail  
and the bottom of the mounting hook.  
Fixed  
Portion  
Back Cane  
Internal Mounting  
Screw  
5. Reinstallthesleeve, lockwasher, andinternalmount-  
ing screw into the fixed release clamp and torque to  
75- inch pounds.  
FIGURE 3- FIXED RELEASE CLAMPS FOR BACK  
Quick Release Clam ps For Seat (FIGURE 4)  
6. Repeat STEPS 1-5 for other side.  
7. Once fixed release mounting clamps are secured, do  
one (1) of follow ing:  
NOTE: Refer to INSTALLATION WARNING in the  
SAFETY SUMMARY before proceeding.  
A. RefertoQUICKRELEASECLAMPSFORSEAT  
in PROCEDURE 2 of this instruction sheet.  
NOTE: The quick release and fixed release clamps are  
designed to fit either 1-inch rail tubing or, with insert pro-  
vided, 7/8-inch rail tubing.  
B. RefertoUSINGCLAMPSinthisinstructionsheet.  
1. Removethesleeve,lockwasher,andinternalthreaded  
mounting screw from the quick release clamp (DE-  
TAIL “C”).  
2. Place the quick release clamp on the seat rail.  
3. Ifquickreleaseclampisnottightlyfittedaroundseatrail  
tubing, installinsertprovidedasshowninDETAILC”.  
3
 
Quick Release (FIGURE 6)  
DETAIL C”  
Internal  
Mounting  
Screw  
1. To unlock, push down on the release tab of the quick  
release rail clamps.  
Insert  
2. To lock, push down on the thumb-like feature of the  
quick release rail clamps.  
Lock Washer  
Sleeve  
TO LOCK APPLY  
PRESSURE HERE  
TO UNLOCK APP
PRESSURE HERE  
Back Cane  
Fixed  
Fixed  
Portion  
Mounting  
Hooks  
Release  
Portion  
Portion  
Wheelchair  
Quick Release  
Clamp  
Frame  
Fixed Release  
Clamp  
Mounting  
Quick Release  
Hook  
Rail Clamp  
FIGURE 4 - QUICK RELEASE AND FIXED  
RELEASE CLAMPS FOR SEAT  
FIGURE 6 - USING CLAMPS - QUICK RELEASE  
USING CLAMPS  
Twist Release (FIGURE 5)  
1. To unlock cane clamp, twist away from back cane.  
2. To lock the cane clamp, twist in toward the back.  
Twist Release  
TOP VIEW  
Cane Clamp  
ck  
Unlock  
Mounting  
Hook  
Back Cane  
FIGURE 5 - USING CLAMPS - TWIST RELEASE  
Invacare Corporation  
USA  
Canada  
One InvacareWay  
Elyria,Ohio USA  
44036-2125  
5970 ChedworthWay  
Mississauga, Ontario  
L5R 3T9, Canada  
905-890-8838  
Invacare is a registered trademark of Invacare Corporation.  
Yes,you can is a trademark of Invacare Corporation.  
© 2001 Invacare Corporation  
800-333-6900  
Form No.97-186 Part No.1074563 Rev C (1) 03/01  
 

Ingersoll Rand Heat Pump 650752 User Manual
Intel Switch SBC 455 User Manual
Jacuzzi Hot Tub 9180 User Manual
Jonsered Chainsaw 2159 User Manual
JVC Portable CD Player RD T5BU User Manual
JVC Projector LX D1010 User Manual
Kalorik Cooktop 30035 User Manual
Kenwood CD Player KDC X915 KDC X815 KDC 9015 User Manual
Knoll Systems Projector LED1081 User Manual
Kompernass Rice Cooker KH 1558 User Manual