Invacare 8000 Alternating Pressure Mattress
Assembly, InstallationandOperatingInstructions
Model No. CG8000
NOTE: The above model number contains one (1) Alternating Pressure Mattress and one (1)
Power Unit.
NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact
Carrier/Dealer for further instruction.
SAFETY SUMMARY
To ensure the safe installation of the Invacare 8000 Alternating Pressure
Mattress and Power Unit, these instructions MUST be followed:
WARNING
DO NOT install or use this equipment without first reading and
understanding this instruction sheet. If you are unable to understand the
Warnings, Cautions or Instructions, contact a healthcare professional,
dealer or technical personnel before attempting to install this equipment -
otherwise, injury or damage may occur.
DO NOT use the mattress near an open flame or while smoking.
Inspect power cord, plug and air hoses of the Invacare 8000 Alternating
Pressure Mattress/Power Unit for breaks, tears, or kinks. If damage is
found, DO NOT use.
DO NOT, under any circumstances, cut or remove the round grounding
prong from any plug used with or for Invacare products. Devices are
equipped with three-prong (grounding) plugs for protection against
possible shock hazards. Where a two-prong wall receptacle is encountered,
it is the personal responsibility and obligation of the customer to contact a
qualified electrician and have the two-prong receptacle replaced with a
properly grounded three-prong wall receptacle in accordance with the
National Electrical Code. If you must use an extension cord, use ONLY a
three-wire extension cord having the same or higher electrical rating as the
device being connected.
DO NOT place hot objects (for example: heating pads, electric blankets,
etc.) on top of the mattress. This may weaken the mattress material.
Use extreme care when handling sharp objects such as needles near the
mattress.
Do NOT inflate mattress of an OCCUPIED bed.
The Alternating Pressure Mattress has a weight limitation of 250 lbs. (114 kg.).
The Invacare 8000 APM MUST be installed on medical bed frames or medical-
grade home care beds with side rails. After placing the patient on the mattress,
verify the side rails provide adequate protection for the patient. The side rails
MUST be in the raised position, whenever a patient is on the bed.
INVACARE 8000 PRESSURE MATTRESS
Part No. 1078996 Rev. B
1
Power Unit Air
Hose Quick
Disconnect
Power
Unit
Cushion
Fittings
Transport Mat
Cushion
Mattress Air Hose
Quick Disconnect
Power
Unit
Knob
CPR Plugs
+MAX
Setting
Power
Switch
-MIN
Setting
FIGURE 2- INFLATING THE MATTRESS
INSTALLING/REMOVING THERAPY PAD (FIGURE 3)
INSTALLING
1. Position therapy pad over mattress.
2. Insert one (1) of the ten (10) straps into
open latch as shown in FIGURE 3.
3. Pull strap until therapy pad fits tight
around mattress.
4. Push down on latch to secure.
Strap
5. Repeat STEPS 2 - 4 for remaining
Latch
nine (9) straps.
6. Secure mattress base to the bed frame.
Refer to SECURING MATTRESS
BASE TO BED FRAME in this
instruction sheet.
REMOVING
1. Remove patient from bed.
2. Pull up on one (1) of the ten (10)
FIGURE 3 - INSTALLING/REMOVING
THERAPY PAD
latches that secure the therapy pad
to the mattress.
3. Remove strap from latch.
4. Repeat STEPS 2 - 3 for remaining nine (9) latches.
5. Remove therapy pad from mattress.
Part No. 1078996 Rev. B
INVACARE 8000 PRESSURE MATTRESS
3
SECURING MATTRESS BASE TO BED FRAME (FIGURE 4)
1. Wrap one (1) of the ten (10) straps on
the mattress around the bed frame.
Double D-rings
2. Insert strap into the two (2) double D-
rings.
3. Feed strap back through only one (1) of
the double D-rings.
4. Pull the strap tight to secure the mattress
base to the bed frame.
5. Repeat STEPS 1 - 4 for the remaining
nine (9) double D-rings.
NOTE: Each SIDE contains three (3) double D-rings
and each END contains two (2) double D-rings for
a total of ten (10) double D-rings.
6. Adjust the mattress to the proper
firmness. Refer to PLACING
PATIENT ON MATTRESS AND
ADJUSTING FIRMNESS in this
instruction sheet.
FIGURE 4 - SECURING MATTRESS BASE
TO BED FRAME
PLACING PATIENT ON MATTRESS AND ADJUSTING
FIRMNESS (FIGURE 5)
NOTE: Refer to WARNINGS in the SAFETY SUMMARY of this instruction sheet.
1. Place patient on the mattress.
2. Check the level that the patient sinks into mattress.
NOTE: The pressure of the power unit can be adjusted to provide maximum effectiveness and
pressure relief for the patient.
NOTE: The pressure can be adjusted with a range from -MIN to +MAX.
NOTE: Every other cushion inside the mattress is connected together known as a chamber. The
mattress consists of two (2) chambers.
NOTE: The power unit will cycle every eight (8) minutes. It will alternate inflating and deflating the
two (2) air chambers.
NOTE: The patients body should sink approximately 1/3 into the mattress.
3. If the level is unacceptable, do one (1) of the following:
A. To increase firmness - turn knob towards +MAX setting.
B. To decrease firmness - turn knob towards -MIN setting.
NOTE: After adjusting the knob, wait ten (10) minutes before rechecking the level the patient sinks
into mattress.
4. Repeat STEP 3 until the patients body sinks 1/3 into the mattress.
INVACARE 8000 PRESSURE MATTRESS
Part No. 1078996 Rev. B
4
Power Unit
Knob
Power Switch
+MAX Setting
-MIN
Setting
FIGURE 5 - PLACING PATIENT ON MATTRESS
AND ADJUSTING FIRMNESS
DEFLATING MATTRESS (FIGURE 6)
NOTE: Alternating cushions are connected together to form a chamber. The mattress consists of
two (2) chambers.
DETAIL “A”
STANDARD DEFLATION
Power Unit
1. Remove therapy pad. Refer to
Power Unit Air Hose
Quick Disconnect
INSTALLING/REMOVING
THERAPY PAD in this instruction sheet.
2. Disconnect the two (2) power unit air
hose quick disconnects from the two (2)
mattress air hose quick disconnects as
shown in DETAIL “A”.
Mattress Air
Hose Quick
Disconnect
3. Fold the mattress in half to force the air out.
4. Before re-inflation is possible, connect
the two (2) power unit air hose quick
disconnects to the two (2) mattress air
hose quick disconnects.
Manifold
5. Inflate the mattress. Refer to
INFLATING THE MATTRESS in
this instruction sheet.
RAPID (CPR) DEFLATION
CPR Plugs
1. Pull the two (2) CPR straps labeled
“PULL CPR” away from mattress.
NOTE: Using the “PULL CPR” straps will disconnect
the CPR plugs from the manifold, which allows the
two (2) chambers to deflate.
2. Before re-inflation is possible, install the
CPR plugs on the CPR straps into the
fittings on the manifold.
3. Inflate the mattress. Refer to
INFLATING THE MATTRESS in
this instruction sheet.
FIGURE 6 - DEFLATING MATTRESS
Part No. 1078996 Rev. B
INVACARE 8000 PRESSURE MATTRESS
5
REPLACING CUSHION(S) (FIGURE 7)
NOTE: Refer to WARNINGS in the SAFETY SUMMARY of this instruction sheet.
1. Remove patient from bed.
2. Remove the therapy pad. Refer to INSTALLING/REMOVING THERAPY PAD
in this instruction sheet.
3. Unbutton the EXISTING cushion from the mattress base.
4. Repeat STEP 3 for opposite side of the cushion.
5. Pull the cushion fitting away from the manifold fitting to remove the cushion from
the mattress.
NOTE: Alternating cushions are connected together to form a chamber. The mattress consists of
two (2) chambers.
NOTE: The cushions in the same chamber as the one removed in STEP 5 will deflate when the
fittings are removed.
6. Position NEW cushion into mattress.
7. Insert cushion fitting into manifold fitting to secure.
8. Button the cushion(s) to secure to the mattress base.
9. If more cushions need replacing, repeat STEPS 3 - 8.
10. Inflate the mattress. Refer to INFLATING THE MATTRESS in this instruction
sheet.
Therapy
Pad
Button Holes
Manifold
Manifold Fitting
Mattress Base
Cushion Fitting
Button
Cushion
FIGURE 7- REPLACING CUSHION(S)
CARE AND MAINTENANCE
1. The mattress can be cleaned by wiping it with a germicidal disinfectant solution.
2. The mattress therapy pad is machine washable. Air dry at a cool temperature.
INVACARE 8000 PRESSURE MATTRESS
Part No. 1078996 Rev. B
6
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY
WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED
AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights
which vary from state to state.
Invacare warrants its product to be free from defects in materials and workmanship
for one(1) year on the pump and six (6) months on the mattress for the original
purchaser. If within such warranty period any such product shall be proven to be
defective, such product shall be repaired or replaced, at Invacare's option. This
warranty does not include any labor or shipping charges incurred in replacement part
installation or repair of any such product. Invacare's sole obligation and your exclusive
remedy under this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your
Invacare product. In the event you do not receive satisfactory warranty service, please
write directly to Invacare at the address on the next page. Provide dealer's name,
address, model number, date of purchase, indicate nature of the defect and, if the
product is serialized, indicate the serial number.
Invacare Corporation will issue a return authorization. The defective unit or parts
must be returned for warranty inspection using the serial number, when applicable, as
identification within thirty (30) days of return authorization date. DO NOT return
products to our factory without our prior consent. C.O.D. shipments will be refused;
please prepay shipping charges.
LIMITATIONS AND EXCLUSIONS: THIS WARRANTY SHALL NOT APPLY TO
PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO
THE ENCLOSED INSTRUCTIONS. IN ADDITION, THE FOREGOING
WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE
SERIAL NUMBER HAS BEEN REMOVED OR DEFACED; PRODUCTS
SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION,
MAINTENANCE OR STORAGE; PRODUCTS MODIFIED WITHOUT
INVACARE'S EXPRESS WRITTEN CONSENT (INCLUDING, BUT NOT
LIMITED TO: MODIFICATION THROUGH THE USE OF UNAUTHORIZED
PARTS OR ATTACHMENTS): PRODUCTS DAMAGED BY REASON OF
REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT
OF INVACARE; PRODUCTS DAMAGED BY CIRCUMSTANCES BEYOND
INVACARE'S CONTROL; PRODUCTS REPAIRED BY ANYONE OTHER THAN
AN AUTHORIZED INVACARE DEALER. SUCH EVALUATION SHALL BE
SOLELY DETERMINED BY INVACARE.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES WHATSOEVER, WHETHER EXPRESSED OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND
FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR
VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE LIMITED TO
REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PERSUANT TO
THE TERMS CONTAINED HEREIN. THE APPLICATION OF ANY IMPLIED
WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION
OF THE EXPRESS WARRANTY PROVIDED HEREIN. INVACARE SHALL NOT
BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/
PROVINCIAL LAWS AND REQUIREMENTS.
Part No. 1078996 Rev. B
INVACARE 8000 PRESSURE MATTRESS
7
USA
Canada
One Invacare Way
Elyria, Ohio USA
44036-2125
570 Matheson Blvd E Unit 8 Invacare is a registered trademark of
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
Invacare Corporation.
Yes, you can. is a trademark of Invacare
Corporation.
800-333-6900
© 2003 Invacare Corporation
Part No. 1078996
Rev B - 05/03
|